Stainless Steel Commercial Countertop Gas Fryer Deep Fryer (LPG) 2 Basket.

How to Install

***Fried Baskets:

1. Snap the handle into the frying basket recess.

2. Screw the head of the handle firmly inward.

***Foot Pad:

1. Place the spacer on the side of the foot pad with the hole.

2. Screw firmly through the spacer and foot.

3. Put the foot pad on the machine and you are done.

How to Use:

1.Connect the gas pipeline and check if it is firm.

2.Turn on the gas regulating valve or the gas system switch of the gas tank, lightly press the lighter to rotate and press (to the left) about 90 degrees, a sound will be heard, and the electric spark will ignite the burner to confirm that the fire has been ignited. Let go, the firepower is at its strongest.

3.The adjustment of the firepower is within the range of 90 degrees from the left and right upper corners of the knob. When the stove is used for the first time, a fire may not be able to ignite, because the pipe is not full of gas, so you can repeat the firing action two or three times to remove the air.

4.Air conditioning: All kinds of gas need to be mixed with air for combustion. Before the burner mixing tube, there is an air regulating plate for adjusting the amount of extraction air.

5.Turn off the flame: Turn the knob back to the original vertical position, and all flames can be extinguished when you hear the reset sound. After use, please turn off all switches.

Common Failure Causes and Troubleshooting Methods

***Without Ignition:

1. The cylinder valve is not open. (Unscrew the valve )

2. Air is mixed into the trachea. (Repeat 3Times)

3. The ignition nozzle is blocked by the burner nozzle. (Insert a thin iron wire into the nozzle hole）

***Electronic Ignition Dim or Malfunction:

1. Improper distance between firing needle and firing switch. (The correct position is 3.5-4mm)

2. The firing needle is dirty. (Wipe off with a dry cloth or emery cloth)

3. Piezoelectric ceramic components fail. (Replace piezoelectric ceramics)

***Abnormal Burning:

1. The fire hole is blocked by dirt. (Remove dirt)

2. Insufficient air pressure. (Replace with new gas)

3. Improper air conditioning. (Adjust the air valve)

Cleaning and Maintenance

1. During cleaning and maintenance, please always clean up the dirt and oil pan in the pot and all switches should be turned off to prevent accidents.

2. If it will not be used for a long time, clean the stainless steel surface with a cloth coated with gasoline first and place it in a well-ventilated place.

3. Please do not change the ventilation space required by the equipment gas.

5. It is strictly forbidden to directly wash the surface of the machine with water to avoid damage to the performance of the equipment.

Notes

1. Please notice that only LPG and low-pressure valves are allowed to be used in this machine（the low-pressure valve is not included）, the high-pressure valve is forbidden to be used. The gas cylinder should be strictly prevented from being inverted. Otherwise, it is very easy to cause an explosion and fire accident and gas nozzle blockage. Gas cylinders must be placed 2 meters away from the machine in a place with a partition wall.

2. Please notice that when used for the first time, the damper must be adjusted to avoid the occurrence of yellow flame or flame separation, which will affect the ignition or even extinguish the flame.

3. Please notice that the damper is at the bottom of the cooker. The flame state can be adjusted to achieve the best combustion effect by simply turning the air flap handle.

4. Please notice that the machine must be placed outside/well ventilated/equipped with a smoke extraction device.

5. Please notice that during use, the operator must not leave the stove and observe the burning of the stove. If the flame goes out, the valve of the gas cylinder should be closed immediately.

6. Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement, and make sure you do not mind before you place the order.