Description
For Odyssey 2 Pro Dual 16bit Direct Acquisition SDR Transceiver Amateur Radio without Walkie-Talkie
General Features:
- The size of PCB is 160 x 83.5mm, suitable for installation in a 180mm x 35mm aluminum alloy outer shell, with a width of 85mm.
- The power supply voltage is 7-15V, which can prevent reverse polarity and overvoltage.
- The current consumption is 350mA when supplied by a 12V power, accompanied by a 1W output driver of 500mA.
- Connect to computer - LAN, Gigabit Ethernet or 100Mbps (depending on firmware).
- Headphones, microphones, CW robotic arm connectors - Mini Jack 3.5mm
- Handheld microphone socket (tangent) - RJ-45, compatible with Yaesu.
- Treble connector - SMA-F
- External device control connector - DB15-F
Receiving Part Features:
- For Odyssey 2 Pro has upgraded the ADC from the original LTC2165 to a larger throughput LTC2208 with a dynamic increase of 10db.
- ADC type: 16 bit LTC2165, one or two independent receiving channels
- Channel separation: -95dB (10MHz)
- Sampling frequency: 122.880MHz
- Acceptable frequency range: 0.1 - 55MHz
- Independent receiver number: 4 - 7 (depends on firmware)
- Sensitivity MDS (500): 127dB, installed UHF: 134dB
- Attenuator: 0 - 30dB, take 1dB as step length
- Blocking dynamic range: 122dB
- 115dB dynamic range is limited by phase noise
- Built-in reference oscillator provided frequency stability: 0.280ppm
- Available width for panoramic observation: 48 - 1536KHz
Transmitting Part Features:
- Working frequency range: 1 - 55MHz
- Output voltage of VNA connector (50ohm load): 0.5V (peak value)
- Output voltage of 1W connector (50ohm load): 10V (peak value)
- VNA output linearity: IMD3 70dB
- Output signal linearity (1W): IMD3 40dB
- Maximum transmitting signal width: 48 - 96Khz (depends on firmware)
Additional function:
- The ability to connect an external stable reference oscillator at 10MHz (logic level 3.3-5V).
- The built-in 12 bit low-frequency ADC can measure output power and reflection signals, as well as SWR.
- Four control lines for additional equipment are used to control the input and output of the transmission mode and the output of the auto tuner.
- A serial data bus for decoders with 16 outputs, which can control ALEX power amplifier boards.
Package Included:
- 1 x Host
General Features:
- The size of PCB is 160 x 83.5mm, suitable for installation in a 180mm x 35mm aluminum alloy outer shell, with a width of 85mm.
- The power supply voltage is 7-15V, which can prevent reverse polarity and overvoltage.
- The current consumption is 350mA when supplied by a 12V power, accompanied by a 1W output driver of 500mA.
- Connect to computer - LAN, Gigabit Ethernet or 100Mbps (depending on firmware).
- Headphones, microphones, CW robotic arm connectors - Mini Jack 3.5mm
- Handheld microphone socket (tangent) - RJ-45, compatible with Yaesu.
- Treble connector - SMA-F
- External device control connector - DB15-F
Receiving Part Features:
- For Odyssey 2 Pro has upgraded the ADC from the original LTC2165 to a larger throughput LTC2208 with a dynamic increase of 10db.
- ADC type: 16 bit LTC2165, one or two independent receiving channels
- Channel separation: -95dB (10MHz)
- Sampling frequency: 122.880MHz
- Acceptable frequency range: 0.1 - 55MHz
- Independent receiver number: 4 - 7 (depends on firmware)
- Sensitivity MDS (500): 127dB, installed UHF: 134dB
- Attenuator: 0 - 30dB, take 1dB as step length
- Blocking dynamic range: 122dB
- 115dB dynamic range is limited by phase noise
- Built-in reference oscillator provided frequency stability: 0.280ppm
- Available width for panoramic observation: 48 - 1536KHz
Transmitting Part Features:
- Working frequency range: 1 - 55MHz
- Output voltage of VNA connector (50ohm load): 0.5V (peak value)
- Output voltage of 1W connector (50ohm load): 10V (peak value)
- VNA output linearity: IMD3 70dB
- Output signal linearity (1W): IMD3 40dB
- Maximum transmitting signal width: 48 - 96Khz (depends on firmware)
Additional function:
- The ability to connect an external stable reference oscillator at 10MHz (logic level 3.3-5V).
- The built-in 12 bit low-frequency ADC can measure output power and reflection signals, as well as SWR.
- Four control lines for additional equipment are used to control the input and output of the transmission mode and the output of the auto tuner.
- A serial data bus for decoders with 16 outputs, which can control ALEX power amplifier boards.
Package Included:
- 1 x Host
Payment Terms
1. We accept PayPal,Payoneer,Visa Card,Google pay,Credit card etc.
2. We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
2. We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
Shipping Terms
1. We will process the order within the handling time ,if you have any questions, please contact us via eBay message or email.
2. For remote regions of DHL/FedEx..., extra shipping costs might be charged. Usually it costs about 30USD-50USD. We will contact you if shipping company informed us your address belongs to remote area. Thanks for your understanding.
2. For remote regions of DHL/FedEx..., extra shipping costs might be charged. Usually it costs about 30USD-50USD. We will contact you if shipping company informed us your address belongs to remote area. Thanks for your understanding.
Return Terms
If you receive the item that not satisfied or defective, please do not open case and kindly notify us within 30 days. We will guide you the returning process for replacement or refund.
Custom Duties & Taxes
1. It is buyer's responsibility to cover the import duties, taxes.We do not charge any taxes and fees, and the possible taxes and fees will be collected by the platform or by third parties such as customs and carriers.
2. Please check with your country's customs office and inform us what/how much should declare before shipping.
2. Please check with your country's customs office and inform us what/how much should declare before shipping.
Feedback
1. Please kindly leave us a positive feedback and 5 star DSR if you satisfied with our product and service. Please feel free to contact us firstly if you have any problem with your order, we are responsible and credible seller and will solve the issue it for you asap.
2. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
2. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.