Features:
- Tinned Copper material for EMI, RFI and ESD Protection
- Flexible and expandable braid design.
- For automotive and industrial use.
- Suitable for use in shielding electric cable from abrasion and radio frequency interference
- Greater than 99 percent pure copper
- Uninsulated braided strand wire with tin plated coating
- Resistant to failure from flexing
- Meets QQ-W-343 standards for uninsulated annealed copper wire
- Flame Rated: VW-1 | For automotive and industrial use: engine tubes and hoses, cable and wire protection | Cut with shears
- RoHS Compliant
Material: Tinned Copper Monofilament
Thickness: 0.12mm
Melt Point: 1084°C RoHS Compliant VW-1 Rating
Working Range: -60°C - 200°C
This tin-plated copper braid is suitable for use in shielding electric cable from abrasion and radio frequency interference.
This braided copper wire is annealed for improved ductility and meets the QQ-W-343 specification for uninsulated wire.
This copper braid is suitable for use in wire shielding applications such as in coaxial cable.
Electrical wire carries an electric current or grounds an electrical device. The amount of current a wire can carry is proportional to its size (gauge), and the wire is generally sheathed with coatings and coverings to insulate and protect it from moisture, chemicals, heat, and abrasion. Copper is the primary material for electrical wire, but alloys are sometimes used to increase its strength or its resistance to chemicals and the environment. Wire can be composed of a single strand or of many smaller strands, depending on its use, and is typically annealed to improve its ductility. Electrical wire is commonly used in industrial, electronic, and automotive applications.
Strong metal fibers made from tinned copper create our Metal Braided Sleeving that can be used in automotive applications to dress-up engines, hose support or wire protection.
The properties of Tinned Copper Metal Braided Sleeving not only protects against cuts and abrasion, but also EMI, RFI and ESD.
With a flexible weave, affordable prices and can easily be cut with shears, covering cables, hoses, tubes and more can be quickly installed for that custom professional look.
1/8"Wide(0.08"Dia) tinned copper braid sleeving is made from 16 strands,each strand consists of 4 wires(0.12mm),Mesh per inch:9
1/4"Wide(0.16"Dia) tinned copper braid sleeving is made from 24 strands,each strand consists of 8 wires(0.12mm),Mesh per inch:7
5/16"Wide(0.20"Dia) tinned copper braid sleeving is made from 48 strands,each strand consists of 6 wires(0.12mm),Mesh per inch:7
1/2"Wide(0.32"Dia) tinned copper braid sleeving is made from 48 strands,each strand consists of 10 wires(0.12mm),Mesh per inch:7
11/16"Wide(0.44"Dia) tinned copper braid sleeving is made from 72 strands,each strand consists of 7 wires(0.12mm),Mesh per inch:7
stop an electrical whine in car stereo,prevent RF interference on a car ignition system,shield wiring in a van conversion
help keep speakers from picking up short wave ham radio
stop getting interference in speaker system from power wires
stop interference on FM radio from other electronics in the home (modems, game consoles, etc)
shield the wire from EMI in audio amplifier
eliminate emi from phono amp stage,isolate power cables
used it for Guitar Pick-Up lead shielding
It provides a “Faraday cage”,if there is the Ham operation close by,you may have to also protect your RCA wires delivering signal to the receiver/amplifier from the DVD,CD,or other sources
It works beautifully for "shielding" long runs of low voltage/amperage signal wiring.Just be sure to properly solder to true/common Ground at both ends of run.In essence, a "Faraday Tube" or a "Faraday Tunnel"!
good to wrap over an ethernet cable to prevent interference
shield 50 ohm coax to stop rf interference from penetrating the coax
shield a webcam wire that is getting electrical interference
shield from electrical wave interference
shield RCA and power cables
shield custom made AC power cords.
shield from unwanted 'noise' or voltage leak
The braided metal shielding is used for EMI/RFI interference shielding over electronic signal wiring.
you can use it as a shield from electromagnetic force (EMF), or you can use it as a ground
use on a boat or other vehicle, the copper shield as a ground for low voltage wiring
shield an uninsulated braided ground strap that is receiving emi
use it to shield guitar wiring. Since the goal for any electric guitar is to achieve zero hum (interference) in your output signal, always ground your shielding or else you may find you have even more humming. Keep the shielding away from contacting any of the pots positive/negative lugs. Just a clean ground wire from the shielding to the back of volume pot if that’s what you’re using for your central ground.
used by putting the wire inside and it is properly grounded rfi can’t get induced or released
used it to protect wires from a cat chewing on them,used this type of braid to shield cables all the time,at least 60 dB if properly grounded on at least one end,Dont put too large of a cable through it such that holes appear between the braids that let RF through.
Can be used as common ground straps, earthing cables and current transmission leads, and where vibrations are unavoidable for high flexibility and connections with low contact and resistance.
Our Earthing braid connections are a reliable and convenient grounding solution for applications that require flexibility and durability.Our earthing braids are UL certified and can be used for all grounding applications.
good to wrap over an ethernet cable to prevent interference
tin copper braided sleeving can cover motorcycle cables for aesthetic purposes and EMI protection
Could thread wires through the braid,Probably have better luck using a thin rod to pull the wires through the braid. Pushing the wires through the braid more than a few inches could be problematic
shield a webcam wire that is getting electrical interference
stop getting interference in speaker system from power wires
shield from electrical wave interference
stop interference on FM radio from other electronics in the home (modems, game consoles, est)
shield 50 ohm coax to stop rf interference from penetrating the coax
good to wrap over an ethernet cable to prevent interference
The braided metal shielding is used for EMI/RFI interference shielding over electronic signal wiring.
shielding RF interference on a car ignition system
This is a finely stranded tinned Copper braided sleeve. The dense braid yields better than 90% coverage. Great for RFI/EMI shielding on wire, or cables.
The primary use of wire sleeving braid is to provide sensitive cables with an EMC screen to shield them against electromagnetic, electrostatic and radio frequency interface.
Optimum screening performance is obtained using copper wire braid that can also be used for earth continuity purposes.
Tin Plated copper is suitable for use at elevated temperatures and for harsh environments or where abrasion is likely to be encountered
Optimum screening performance is obtained using copper wire braid that can also be used for earth continuity purposes.
Tin Plated copper is suitable for use at elevated temperatures and for harsh environments or where abrasion is likely to be encountered