Package 1 Buck Converter Volt Step Down module Features Use a dedicated benchmark IC, and high-precision current sensing resistor, make more stable constant current, (when 20°C to 60°C constant current 5A, temperature drift less than 5%). suitable for LED driver. Fixed turn lamp current is 0.1 times the current value (When charging, used to identify whether the battery is fully charged); High output current, the max output current can reach 8A. Low output ripple , high frequency capacitor reduces output ripple. Specifications Module Properties: non-isolated step-down module, constant current and constant voltage module (CC CV), charging module Input voltage: 7-40V Output voltage: 1.2-35V (continuously adjustable) Output Current: 8A Max ( power tube temperature exceeds 65°C please add cooling fan ) Constant current range :0.2-8A ( adjustable ) Turn lamp current : constant current value * ( 0.1 ) , turn lamp current and constant current value linkage.For example, constant current value 3A, turn lamp current is set to 0.1 times constant current(0.1 * 3A = 0.3A). When adjust the constant current to 2A , then turn lamp current is 0.1 times constant current (0.1 * 2A = 0.2A). Turn lamp current is fixed to 0.1 time in this version( actually turn lamp current value is probably not very accurate ), it is for identify whether the battery is fully charged. Dropout voltage: 1V Output Power: Maximum power is about 300W, power tube temperature exceeds 65 degrees please add fan. Conversion efficiency : up to approximately 95% ( the higher output voltage, the higher the efficiency ) Operating frequency: 180KHZ Output ripple : 20M bandwidth ( for reference only ) Input 24V Output 12V 5A ripple around 50mV ( excluding noise ) Operating temperature : Industrial grade (-40 °C to +85 °C) No-load current : Typical 20mA (24V step down to 12V) Load regulation : ± 1% ( constant voltage) Voltage regulation : ± 1% Constant accuracy and temperature: actual test , the module temperature changes from 25 degrees to 60 degrees , the change of the constant current value is less than 5% ( constant current value 5A) Dynamic response speed : 5% 200uS Potentiometer adjustment: clockwise ( increase ) , counterclockwise ( decrease ). The potentiometer close to the input port is for voltage adjust (CV), the potentiometer close to the output port is for current adjust(CC). Indicator : double color indicator. When charging the indicator is RED, fully charged is GREEN( No load is green ). Output short circuit protection : Yes , constant current ( constant current value you set) Input Reverse Polarity Protection: None Output prevent backflow : None. Wiring: Terminal Size:65(L)*47(W)*23.5(H) mm Applications High-power LED constant current drive , Lithium battery(or Iron battery) charge, 6V, 12V, 14V, 24V battery charge , Nickel-cadmium nickel-metal hydride battery ( battery pack ) charge , Solar panels and wind turbines Battery charge: Make sure of the battery float voltage and charging current that you need, the input voltage of the module. Adjust the constant voltage potentiometer, adjust the output voltage to about 5V. Use the multimeter in 10A current scale to measure output short-circuit current, and adjust the current potentiometer to make sure the output current to the expected charging current value. Adjust the constant voltage potentiometer make the output voltage reaches the float voltage; Connected to the battery, try to charge. (1,2,3,4 steps to connect the power module input, output no-load does not connect battery.) LED constant current drive: Make sure operating current and Max operating Voltage of the LED you need to drive. Adjust the constant voltage potentiometer, adjust the output voltage to about 5V. Use the multimeter in 10A current scale to measure output short-circuit current, and adjust the current potentiometer to make sure the output current to the expected LED operating current. Adjust constant voltage potentiometer make the output voltage reach the maximum LED operating voltage. Connect LED, test. (1,2,3,4 steps to connect the power module input, output No-load does not connect LED.) |
| |
(1) We
strive to provide the best service as possible, commit to resolve all problems
and give fast shipping.
(2) Please contact us before giving any
negative feedback. If you have any questions, please do not hesitate to
contact us.
| Payment |
(1) All payments must be prepaid and cleared.
(2) We only accept Paypal payment. After checkout, please make through Paypal service.
| Shipping |
(1) Buyer is responsible for any
incorrect address and undeliverable address. We reserve the right to charge the shipping fee again for returned items due to
wrong address.
We take the paypal address as your shipping address.
(2) Your order will be shipped
within 24 hours after payment is cleared (Sat. & Sun.
excluded and holidays)
(3) We ship orders using USPS (United States
Postal Service). The shipment usually takes 2-4 business days, excluding
holidays, Saturday and Sunday
(4) Local pick up is not
available.
(5) No International
Shipping.
| Warranty |
(1) This product has a 30-day
warranty.
(2) Warranty does not extended to any products that are
buyer's negligence, abuse, misuse, improper installation or physically
damaged on the buyer or user's part.
(3) Please contact us before making a
replacement or refund.
(4) In case of returning, buyer must pay their own
postage and shipping fees for replacement or refund. We will provide
replacement or refund after product is received.
|
|
|
| |||||||