|
|
||||||
|
|
|
|
|||
|
|
|
|
|||
Fitment:
Dodge Durango 3.6L 2011-2022
Dodge Durango 5.7L 2011-2022
Dodge Durango 6.2L 2021
Dodge Durango 6.4L 2020-2022
Jeep Grand Cherokee 3.0L 2014-2021
Jeep Grand Cherokee 3.6L 2011-2022
Jeep Grand Cherokee 5.7L 2012-2022
Jeep Grand Cherokee 6.4L 2012-2017
Location: Front Left & Right
Note1: 2014-2017 Jeep Grand Cherokee 4WD, AWD, with Quadra Trac II
Note2: 2018-2022 Jeep Grand Cherokee 3.0L,3.6L,5.7L,4WD, AWD; with 2 Speed Transfer Case; with Quadra Trac II
I installed a replacement CV drive axle and now my ABS light is on and won't go out. Why?
When the replacement drive axle was installed, the sensor ring, sensor, or sensor wiring on or near the axle was damaged, causing an erratic speed signal to the ABS module and setting the light on.
When I cut the wheel hard and step on the gas, I hear loud clicking and snapping. What's making that noise?
The most likely cause is a defective or worn outer CV drive axle joint. It may be time to get it replaced.
When I step on the gas, I hear a loud thump and feel a bad vibration. What's wrong?
The most likely cause is the drive train shifting in the chassis due to a broken engine mount or hardware, causing misalignment of the CV drive axle and causing the inner joint to bind or hang up.
I hear a grinding noise from the front end while driving and see grease on the chassis and suspension. What is causing this?
The most likely problem is the outer CV drive axle boot has ruptured, causing the grease to leak out, allowing contamination (water and dirt) to enter and damage the joint.
I removed both CV drive axles at the same time and now I am having problems reinstalling them. What can I do?
The transaxle gear alignment has been lost. On some vehicles it will be necessary to disassemble the transaxle to properly align the output gears. ALWAYS remove and install one CV drive axle at a time.
The old CV Drive Axle has a locking style (prevailing torque) nut. Should I reuse it?
NO! A prevailing torque lock nut should never be reused. Always discard the old nut and install a new one.
The CV Drive Axle outboard joint stub shaft is stuck in the hub assembly. What's the best way to remove it?
Always use the proper press type tool to remove the old stub shaft. NEVER strike the outer joint stub shaft with a hammer. It will damage the unit and possibly do damage to the hub bearing assembly.
Is it OK to use an impact hammer to install the retaining nut?
Never use an impact wrench to install the retaining nut on the CV Drive Axle. Always use a torque wrench and torque the nut to manufacture's specifications.
When I replace the CV drive axles, should I reuse the old seals?
When replacing CV Drive Axle assemblies, always install new transaxle seals to avoid leaking.
Can I let the CV Drive Axles hang while I am working on the car?
Never allow the CV Drive Axles to hang unsupported. This can lead to axle separation and damage to the inner joint.
The wheels wobble when I make a turn. What's the problem?
The most likely cause is a broken bearing cage due to excessive torque load. This is typically an outboar
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
- Instant Paypal payment is the preferred method of payment.
- We will only ship to the confirmed Paypal shipping address given with the payment.
- We do not offer local pickups.
1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
3. The images shown are not the actual item and are for your reference only.
4. Fast shipping:All our packages use USPS Package Service
5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
1. You have 7 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
4. Return shipping is to be paid by the Buyer.
- We are always been trying to provide best service and reliable products for every customer.
- If you are satisfed with the product you recieved,please leave us positive feedback.
- If you are not satisfied for any reason, please do not be quick to leave negative or neutral feedback.We will work hard to make sure every customer 100 percent satisfied, and reslove any problem for you.