24" 6-Outlet Hardwired Power Strip, H206VW

Features

• 24" /  0.61m Durable Metal Housing Hardwired Power Strip, No Ears (Mounting Tabs on Both Ends), White
• 6 White US NEMA 5-15R Outlets, Vertical Orientation
• Hardwired without Power Cord for Mounting at Your Desired Location
• 6 Easily Punched off Knockouts on Each Side (Top, Bottom Cover, Both Sides and Ends)
• ETL Approved and Listed (Conforms to UL 5 and CAN/CSA C22.2 No. 62)
• Easy On/Off Back Cover for Wire Connection
• Wires Readily Striped for Easier Removal and Faster Installation
• Great Item for Contractors, Electric Engineers, Electricians, Installers as well as DIYers

Specification

Model #:	H206VW
Description:	24" Hardwired Power Strip, White
Measurement:	L24" x W1.61" x H1.16" (610 x 41 x 29.5mm)*
TR Outlets:	N/A
ALCI Capable:	N/A
Receptacles:	6 White NEMA-5-15R Vertical Outlets
Outlet Spacing:	2.91" / 74mm (Center to Center)
USB Port:	N/A
Electrical Rating:	110-125V/15A/60Hz
Full Load:	1875VA (Recommended Max Load 1440W)
Switch:	N/A
Circuit Breaker:	N/A
Knockout Cord Exit:	6 (Top, Bottom, Both Sides & Ends), Dia 0.83"/21mm
Knockout Rim to End:	Top/Bottom Cover/Both Sides: 1.87"/47.5mm
Mounting on Back:	Additional Mounting Holes Available
Ears (Mounting Tabs):	N/A
Mounting Clips:	Spring Steel Mounting Clips included
Other:	N/A

Installation work of this unit must be done by a professional, a licensed electrician or an electric engineer.

Never install this unit during a thunder storm.

Switch off the power before you start installation work.

This unit is for indoor use only.

This unit is not intended for use in or around wet or potentially wet areas including, but not limited to, aquariums, saunas, showers and fountains.

Risk of Electric Shock!

1. Turn off electricity in the house
2. Decide where to place this Hardwired Power Strip unit
3. Choose the knockout to be used for cord exit, then gently punch it off with the back of a screw driver or other tool handy
4. Unscrew the back cover off the unit with a philips screw driver
5. Take out the white/transparent plastic insulation sheet, and use a pair of scissors to cut a hole on it (about 3/4″ in diameter, or big enough for) WHERE the wires will run through. If the bottom knockout on the back cover is to be used for wire connection, a wire clamp connector may not be needed, thus, please ignore step 6, 7 and 9 below
6. Put on the 3/4″ wire clamp connector in place. Secure its installation by tightening the big ring screw (which is inside the casing, with the pair of slip joint pliers
7. Run the wires through the wire clamp connector, from outside into the Unit. In case bottom knockout on the back cover is to be used for wire connection, please run the wires through the back cover first and then the plastic insulation sheet , now with the knockout coin punched off, from outside to inside
8. Match the colored wires and secure the wire connection with proper wire connectors
9. Tighten the two pressure screws properly on the wire clamp connector
10. Place the plastic insulation sheet back and screw the back cover on
11. Mount the unit:
    A) For unit with ears (mounting tabs on both ends): mount the unit through the ears with screws provided
    B) For unit without ears, place the unit where it is intended to be, mark where to install clips, secure the clips with screws provided. Then snap the unit in onto the clips
    C) For models without ears up to 24″, and models with ears above 30″, mounting holes on the back cover could be used to secure the unit (but a unit CANNOT be installed with such mounting holes if the unit is to be placed against a wall/cabinet on the side since the unit cannot be reinstalled onto the back cover). Then, please mount the back cover first and then carefully screw the unit onto the back cover
12. Turn electricity back on, it is ready to go